Pt7137 installation software

Connect the power adapter jack to the Network Camera before plugging in to the power socket. This will reduce the risk of accidental electric shock. Upon powering up, the front red LED will become lighted first and then the device will go through booting process. During the booting process, red, blue and green LEDs will be on. After booted, the Network Camera will standby for getting IP address. The Network Camera will first detect Ethernet. During the searching and connecting process to the wireless access point or station, the red LED of the Network Camera will flash every second.

Operating in either network mode, the green LED will flash every second as heartbeat to indicate alive. If the red LED is blinking, please check the network connections. Make sure the Ethernet is firmly connected to a switch hub. After attaching the Ethernet cable plug in the power adapter. Once any access point is found, the LED will turn blue to wait for installation.

If the network environment cannot meet the default settings, install Network Camera in Ethernet to proceed with wireless LAN configuration. There may be several entries shown in the window. The Administrator may differentiate the Network Cameras with the serial number. They may be from the DHCP server. The method of finding IP address is seeking from If any of the address inside this range is free, the Network Camera will be assigned to this IP address, and its subnet mask would be If none of the addresses is free, the Network Camera will try the range from There may be many Network Cameras in the local network.

Users can differentiate the Network Cameras with the serial number. The serial number is printed on the labels on the carton and the back of the Network Camera body.

The Network Camera can be connected either before or immediately after software installation onto the Local Area Network. The Administrator should complete the network settings on the configuration page, including the correct subnet mask and IP address of gateway and DNS.

Ask your network administrator or Internet service provider for the detail information. By default the Network Camera requires the Administrator to run installation every time it reboots. If the network settings are to remain unchanged, disable the Install option. The Administrator should immediately implement a new password as a matter of prudent security practice. The Administrator can set up a maximum of twenty 20 user accounts. Each user can access the Network Camera except to perform system configuration.

Some critical functions are exclusive for the Administrator, such as system configuration, user administration, and software upgrades. Once the password is changed, the browser will display an authentication window to ask for the new password. The only option is to restore to the original factory default settings. After opening the Web browser and typing in the URL of the Network Camera, a dialogue window pops up to request a username and password.

Upon successful authentication, the following figure is displayed. The foreground is the login window and the background shows the message if authentication fails. The user may check the option box to save the password for future convenience.

This option is not available to the Administrator for obvious reason. For the initial access to the Network Camera in Windows, the web browser may prompt for permission to install a new plug-in for the Network Camera. If the highest security level is set, the computer may prohibit any installation and execution attempt. This plug-in has been registered for certificate and is used to display the video in the browser. Users may click on to proceed. If the web browser does not allow the user to continue to install, check the Internet security option and lower the security levels or contact your IT or networking supervisor for help.

Configuration functions : The camera can be configured using these user interfaces. Camera View : What the camera sees. Click on the configuration link to the left of the image window to enter the configuration page. Clicking on this button links you to the client setting pages, please check the following session for more details.

The camera view provides not only the live video, but also a way to aim the Network Camera to different target. Using mouse to click on the target inside the video will command the Network Camera to aim at the target. This feature allows users to open a digital zoom control window to specify the zoom. The button is the same one as. The Home button centers the camera. This button commands the camera to pan from the current position to the left-most and then to the right-most position.

After panning, the camera returns to the original position. After one patrol cycle, the camera returns to the original position. The user may click on to install the plug-in.

If the web browser does not allow the user to complete the installation, check the Internet security to lower the security level or contact your IT or networking supervisor. There are two settings for the client side. The UDP protocol allows for more real-time audio and video streams. However, some packets may be lost due to network burst traffic and images may be obscured. The TCP protocol allows for less packet loss and produces a more accurate video display. The downside with this protocol is that the real-time effect is worse than that with the UDP protocol.

If no special need is required, UDP protocol is recommended. The selected protocol will be recorded in the user's PC and will be used for the next connection. If the network environment is changed, or the user wants to let the web browser to detect again, manually select the UDP protocol, save, and return HOME to re-connect. Best performance generally equates to the fastest image refresh rate with the best video quality, and at the lowest network bandwidth as possible.

Due to the limitation of the bandwidth for 3GPP, only x size video is supported for cell phone viewing. To achieve good real-time visual effect, the network bandwidth should be large enough to allow a transmission rate of greater than 20 image frames per second. The maximum frame rate is If your network bandwidth is more than Kbps, you can fix the bit rate according to your bandwidth and set the maximum frame rate to 30 fps.

If the images vary dramatically in your environment, you may want to slow the maximum frame rate down to 20 fps in order to lower the rate of data transmission. This allows for better video quality and the human eyes cannot readily detect the differences between those of 20, 25, or 30 frames per second. In a slow network, greater frame rate results in blur images. Video quality performance will vary somewhat due to the number of users viewing on the network; even when the parameters have initially been finely tuned.

The images may suffer a time delay due to a slower connection. The delay will also increase with added number of users. Welcome to ManualMachine. We have sent a verification link to to complete your registration.

The product must be installed and protected in a location that is not easily accessible, and is away from impacts or heavy vibration. For example, at the location where the surveillance cameras are looking down or installed at high positions such as on a pole, wall, or at least 3 meters above the ground.

Bijvoorbeeld, op de plek waar de bewakingscamera's naar beneden staan gericht of zijn. Il prodotto deve essere installato e protetto in un luogo non facilmente accessibile e lontano da urti o forti vibrazioni. Ad esempio, nel luogo in cui le telecamere di sorveglianza guardano verso il basso o sono installate in posizioni elevate, ad esempio su un palo, un muro o almeno 3 metri dal suolo. Prima dell'installazione, il prodotto deve essere conservato in un ambiente asciutto e ventilato.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:. Produk harus dipasang dan dilindungi di lokasi yang tidak mudah dijangkau, serta jauh dari benturan atau getaran hebat.

Misalnya, di lokasi di mana kamera pengawasan mengarah ke bawah atau dipasang di posisi tinggi seperti di atas tiang, tembok, atau minimal 3 meter di atas tanah. Users can directly employ the built-in RTSP-compatible multimedia software on 3G cellular phones to view streaming video from the camera without the need to download and install additional applications.

The product should be used in compliance with local laws and regulations. Het product dient te worden gebruikt conform lokale wetgeving en regelgeving. Do not install the product on an unstable mount or surface. Installeer het product niet op een onstabiele standaard of oppervlak.

Do not disassemble the camera or perform maintenance task when power is connected. Demonteer de camera niet en pleeg geen onderhoud terwijl de stroom is aangesloten.